Replacing uPVC Window Handles
It is easy to change the handles on upvc windows. It is important to make sure that the new handle fits into the spindle cutout in the window mechanism.
If the steps below are followed, any cockspur handle should fit in most windows. The step height of the handle is key.
What to Look for
As time passes, uPVC handles on many windows in the UK can start to show signs of wear and wear and tear. When this happens, the window handle could become shaky or difficult to operate, which makes it necessary to replace it. This is a simple job that is achievable by anyone who is familiar with basic hand tools.
The first step is to ensure that the handle is securely fixed to the frame of the window and in its open position. The next step is to locate the pins or screws that secure the handle in place. They are usually on the inside face of the handle and are removed with a screwdriver, or pliers.
When the handle has become loose, gently pull it away from its hinges. It is then time to find a new handle that is the same design and size. This can be accomplished in a DIY store or online. The procedure should take just five minutes and requires a screwdriver.
The most important thing to consider when replacing a uPVC window handle is its step height. This is the distance from the bottom of the handle to where it rests on the window frame. This is a typical measurement and you should confirm the step height before ordering the replacement handle.
There are several sizes depending on the kind of handle. Inline handles for uPVC windows typically feature lug centers of 31mm There are also cockspur handle types that have 43mm centres. Tilt and turn handles are commonly used on windows made of uPVC, and they feature a specific design that allows windows to be tilted in to allow for ventilation, and then turned to open the window completely.
The most common breakage in uPVC handles is that they crack internally rather than breaking off from the base section. This makes it difficult to open. It is crucial to ensure that the replacement handle is fitted with the same spindle as your original one.
Remove the Old Handle
Incorrectly installed or damaged window handles can cause your double-glazed windows to open or close incorrectly, and can result in them getting stuck. This can be caused by various reasons, including general wear and tear on the handle or corrosion. In these instances it is essential to find replacement handles made of upvc as soon as you can to avoid further damage and loss of function.
One of the first things to do when replacing upvc window handles is to remove the old handle from the window. Start by removing the screw covered when the handle in closed position. This will reveal a screw and once removed, you can then begin to remove the handle. door handle repair is recommended to use an electric screwdriver for this since it will make the task much easier and quicker.
It is also important to note that the handles' screws could be hidden behind caps made of plastic, so it is a good idea to take an Stanley knife to the screw caps and then remove them. Once the old handle is removed, you should then look at the square cut on the base of the handle to make sure that the new window lock handles will work with it. It is crucial to measure the spindle length on the handle you used to replace it with and compare it to the dimensions of the window mechanism spindle cutout.
There are three kinds of upvc handles: Espag handles with a central screw that can be turned either left or right and Cranked handles that have two screws and Spade handles that have arms that are flat and can be used either side of the window made of upvc. It is simple to replace the handle when you have identified one that is suitable. Just put it in place and make sure the spindle is correctly inserted in the lock mechanism. After that, you can then tighten the handle to the window frame. Your replacement upvc handles will now be secure.
Take a measurement of the Spindle
If you're replacing a upvc window handle that has fallen off, it's due to the spindle that holds it in place has become damaged or loose. In some cases, you can tighten the spindle using pins or screws. In some cases, it may be necessary to replace the handle. There are several kinds of window handles made of upvc. There are three types of handles: inline espagnolette cockspur, and tilt-and-turn. Each kind has a distinct method of installing and replacing the handle.
It is crucial to measure the current handle before purchasing an alternative. This will ensure that the handle fits the window properly and be the correct size. All handles are sized in accordance with industry standards, making it easy to find the correct size.
To determine the size of your handle, first remove it from the window by turning it to the open position. You should be able see the size of the pin or screw that holds the handle. Then, use a ruler or tape measure to determine the length of the spindle. Once you have determined the length of the spindle, you can purchase a replacement one with exactly the same size.
The step height of a window handle is also important to take into consideration when buying a replacement. The step height is measured from the base to the point where the handle is positioned on the frame. This usually is about 21mm or 9mm for aluminum and uPVC. To make sure that the new handle will work the gap, drop something into the space to check how far it goes before it meets an obstruction.
Cockspur handles usually have different backset heights based on the style of window they are installed in. Inline Espag handles have a standard height of 43mm centre to centre (2 fixing points). Cockspur handles have different backsets depending on the window they are in. This is because they have an extension spur that extends from the handle and then locks over the cockspur wedge striker plate.
Fit the New Handle
After you've chosen the new handle, ensure that it is aligned with the screw holes on the door. Then, secure it with the screws supplied. Install the latch lever in the same manner as the handle on the main handle when you're replacing the door handle. Then, you can reattach the door trim in order to conceal the screws for mounting and finish the project.
Tips: To remove the metal head from the wedge of wood Hold the handle so that its broad end rests on the floor and use a hammer to tap the thin end of the handle. Be careful not to damage the handle or the spindle.